[Docs] [txt|pdf] [draft-ietf-tewg...] [Tracker] [Diff1] [Diff2]
EXPERIMENTAL
Network Working Group F. Le Faucheur, Ed.
Request for Comments: 4127 Cisco Systems, Inc.
Category: Experimental June 2005
Russian Dolls Bandwidth Constraints Model for
Diffserv-aware MPLS Traffic Engineering
Status of This Memo
This memo defines an Experimental Protocol for the Internet
community. It does not specify an Internet standard of any kind.
Discussion and suggestions for improvement are requested.
Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2005).
Abstract
This document provides specifications for one Bandwidth Constraints
Model for Diffserv-aware MPLS Traffic Engineering, which is referred
to as the Russian Dolls Model.
Table of Contents
1. Introduction ....................................................2
1.1. Specification of Requirements ..............................2
2. Contributing Authors ............................................3
3. Definitions .....................................................4
4. Russian Dolls Model Definition ..................................5
5. Example Formulas for Computing "Unreserved TE-Class [i]" with
Russian Dolls Model .............................................7
6. Receiving Both Maximum Reservable Bandwidth and Bandwidth
Constraints sub-TLVs ............................................8
7. Security Considerations .........................................8
8. IANA Considerations .............................................8
9. Acknowledgements ................................................9
Appendix A: Addressing [DSTE-REQ] Scenarios .......................10
Normative References ..............................................11
Informative References ............................................12
Le Faucheur Experimental [Page 1]
RFC 4127 Russian Dolls Model for DS-TE June 2005
1. Introduction
[DSTE-REQ] presents the Service Providers requirements for support of
Diffserv-aware MPLS Traffic Engineering (DS-TE). This includes the
fundamental requirement to be able to enforce different Bandwidth
Constraints for different classes of traffic.
[DSTE-REQ] also defines the concept of Bandwidth Constraints Model
for DS-TE and states that "The DS-TE technical solution MUST specify
at least one Bandwidth Constraints Model and MAY specify multiple
Bandwidth Constraints Models".
This document provides a detailed description of one particular
Bandwidth Constraints Model for DS-TE which is introduced in
[DSTE-REQ] and called the Russian Dolls Model (RDM).
[DSTE-PROTO] specifies the Interior Gateway Protocol (IGP) and RSVP-
TE signaling extensions for support of DS-TE. These extensions
support RDM.
1.1. Specification of Requirements
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
Le Faucheur Experimental [Page 2]
RFC 4127 Russian Dolls Model for DS-TE June 2005
2. Contributing Authors
This document was the collective work of several authors. The text
and content were contributed by the editor and the co-authors listed
below. (The contact information for the editor appears in the
Editor's Address section.)
Jim Boyle Kireeti Kompella
Protocol Driven Networks, Inc. Juniper Networks, Inc.
1381 Kildaire Farm Road #288 1194 N. Mathilda Ave.
Cary, NC 27511, USA Sunnyvale, CA 94099
Phone: (919) 852-5160 EMail: kireeti@juniper.net
EMail: jboyle@pdnets.com
William Townsend Thomas D. Nadeau
Tenor Networks Cisco Systems, Inc.
100 Nagog Park 250 Apollo Drive
Acton, MA 01720 Chelmsford, MA 01824
Phone: +1-978-264-4900 Phone: +1-978-244-3051
EMail: btownsend@tenornetworks.com EMail: tnadeau@cisco.com
Darek Skalecki
Nortel Networks
3500 Carling Ave,
Nepean K2H 8E9
Phone: +1-613-765-2252
EMail: dareks@nortelnetworks.com
Le Faucheur Experimental [Page 3]
RFC 4127 Russian Dolls Model for DS-TE June 2005
3. Definitions
For readability a number of definitions from [DSTE-REQ] are repeated
here:
Class-Type (CT): the set of Traffic Trunks crossing a link that is
governed by a specific set of bandwidth constraints.
CT is used for the purposes of link bandwidth
allocation, constraint-based routing and admission
control. A given Traffic Trunk belongs to the same
CT on all links.
TE-Class: A pair of:
i. a Class-Type
ii. a preemption priority allowed for that Class-
Type. This means that an LSP transporting a Traffic
Trunk from that Class-Type can use that preemption
priority as the setup priority, the holding
priority, or both.
A number of recovery mechanisms under investigation or specification
in the IETF take advantage of the concept of bandwidth sharing across
particular sets of LSPs. "Shared Mesh Restoration" in [GMPLS-RECOV]
and "Facility-based Computation Model" in [MPLS-BACKUP] are example
mechanisms that increase bandwidth efficiency by sharing bandwidth
across backup LSPs protecting against independent failures. To
ensure that the notion of "Reserved (CTc)" introduced in [DSTE-REQ]
is compatible with such a concept of bandwidth sharing across
multiple LSPs, the wording of the "Reserved (CTc)" definition
provided in [DSTE-REQ] is generalized into the following:
Reserved (CTc): For a given Class-Type CTc ( 0 <= c <= MaxCT ), let
us define "Reserved(CTc)" as the total amount of the
bandwidth reserved by all the established LSPs which
belong to CTc.
With this generalization, the Russian Dolls Model definition provided
in this document is compatible with Shared Mesh Restoration defined
in [GMPLS-RECOV], so that DS-TE and Shared Mesh Protection can
operate simultaneously. This assumes that Shared Mesh Restoration
operates independently within each DS-TE Class-Type and does not
operate across Class-Types (for example, backup LSPs protecting
Primary LSPs of CTx also need to belong to CTx; Excess Traffic LSPs
sharing bandwidth with Backup LSPs of CTx also need to belong to
CTx).
Le Faucheur Experimental [Page 4]
RFC 4127 Russian Dolls Model for DS-TE June 2005
We also introduce the following definition:
Reserved(CTb,q): Let us define "Reserved(CTb,q)" as the total amount
of the bandwidth reserved by all the established
LSPs that belong to CTb and have a holding priority
of q. Note that if q and CTb do not form one of the
8 possible configured TE-Classes, then there cannot
be any established LSPs that belongs to CTb and has
a holding priority of q; therefore, in this case,
Reserved(CTb,q) = 0.
4. Russian Dolls Model Definition
RDM is defined in the following manner:
o Maximum Number of Bandwidth Constraints (MaxBC)=
Maximum Number of Class-Types (MaxCT) = 8
o for each value of b in the range 0 <= b <= (MaxCT - 1):
SUM (Reserved (CTc)) <= BCb,
where the SUM is across all values of c in the
range b <= c <= (MaxCT - 1)
o BC0= Maximum Reservable Bandwidth, so that
SUM (Reserved(CTc)) <= Max-Reservable-Bw,
where the SUM is across all values of c in the
range 0 <= c <= (MaxCT - 1)
A DS-TE LSR implementing RDM MUST support enforcement of Bandwidth
Constraints in compliance with this definition.
Both preemption within a CT and across CTs is allowed.
Where 8 CTs are active, the RDM Bandwidth Constraints can also be
expressed in the following way:
- All LSPs from CT7 use no more than BC7
- All LSPs from CT6 and CT7 use no more than BC6
- All LSPs from CT5, CT6 and CT7 use no more than BC5
- etc.
- All LSPs from CT0, CT1, ..., CT7 use no more than BC0 = "Maximum
Reservable Bandwidth"
Le Faucheur Experimental [Page 5]
RFC 4127 Russian Dolls Model for DS-TE June 2005
Purely for illustration purposes, the diagram below represents the
Russian Dolls Bandwidth Constraints Model in a pictorial manner when
3 Class-Types are active:
I------------------------------------------------------I
I-------------------------------I I
I--------------I I I
I CT2 I CT2+CT1 I CT2+CT1+CT0 I
I--------------I I I
I-------------------------------I I
I------------------------------------------------------I
I-----BC2------>
I----------------------BC1------>
I------------------------------BC0=Max Reservable Bw--->
While simpler Bandwidth Constraints models or, conversely, more
flexible/sophisticated Bandwidth Constraints models can be defined,
the Russian Dolls Model is attractive in some DS-TE environments for
the following reasons:
- Although it is a little less intuitive than the Maximum
Allocation Model (see [DSTE-MAM]), RDM is still a simple model
to conceptualize.
- RDM can be used simultaneously to ensure bandwidth efficiency
and to protect against QoS degradation of all CTs, whether
preemption is used or not.
- RDM can be used in conjunction with preemption to simultaneously
achieve (i) isolation across CTs (so that each CT is guaranteed
its share of bandwidth no matter the level of contention by
other classes), (ii) bandwidth efficiency, and (iii) protection
against QoS degradation of all CTs.
- RDM only requires limited protocol extensions such as the ones
defined in [DSTE-PROTO].
RDM may not be attractive in some DS-TE environments for the
following reasons:
- if the usage of preemption is precluded for some administrative
reason, while RDM can still ensure bandwidth efficiency and
protection against QoS degradation of all CTs, RDM cannot
guarantee isolation across Class-Types.
Additional considerations on the properties of RDM can be found in
[BC-CONS] and [BC-MODEL].
Le Faucheur Experimental [Page 6]
RFC 4127 Russian Dolls Model for DS-TE June 2005
As a simple example usage of the "Russian Dolls" Bandwidth
Constraints Model, a network administrator, using one CT for Voice
(CT1) and one CT for data (CT0), might configure on a given link:
- BC0 = Max-Reservable - Bw = 2.5 Gb/s (i.e., Voice + Data is
limited to 2.5 Gb/s)
- BC1 = 1.5 Gb/s (i.e., Voice is limited to 1.5 Gb/s).
5. Example Formulas for Computing "Unreserved TE-Class [i]" with
Russian Dolls Model
As specified in [DSTE-PROTO], formulas for computing "Unreserved TE-
Class [i]" MUST reflect all of the Bandwidth Constraints relevant to
the CT associated with TE-Class[i], and thus, depend on the Bandwidth
Constraints Model. Thus, a DS-TE LSR implementing RDM MUST reflect
the RDM Bandwidth Constraints defined in section 4 above when
computing "Unreserved TE-Class [i]".
As explained in [DSTE-PROTO], the details of admission control
algorithms, as well as formulas for computing "Unreserved TE-Class
[i]", are outside the scope of the IETF work. Keeping that in mind,
we provide in this section an example for illustration purposes, of
how values for the unreserved bandwidth for TE-Class[i] might be
computed with RDM. In the example, we assume the basic admission
control algorithm, which simply deducts the exact bandwidth of any
established LSP from all of the Bandwidth Constraints relevant to the
CT associated with that LSP.
We assume that:
TE-Class [i] <--> < CTc , preemption p>
in the configured TE-Class mapping.
For readability, formulas are first shown assuming only 3 CTs are
active. The formulas are then extended to cover the cases where more
CTs are used.
If CTc = CT0, then "Unreserved TE-Class [i]" =
[ BC0 - SUM ( Reserved(CTb,q) ) ] for q <= p and 0 <= b <= 2
If CTc = CT1, then "Unreserved TE-Class [i]" =
MIN [
[ BC1 - SUM ( Reserved(CTb,q) ) ] for q <= p and 1 <= b <= 2,
[ BC0 - SUM ( Reserved(CTb,q) ) ] for q <= p and 0 <= b <= 2
]
Le Faucheur Experimental [Page 7]
RFC 4127 Russian Dolls Model for DS-TE June 2005
If CTc = CT2, then "Unreserved TE-Class [i]" =
MIN [
[ BC2 - SUM ( Reserved(CTb,q) ) ] for q <= p and 2 <= b <= 2,
[ BC1 - SUM ( Reserved(CTb,q) ) ] for q <= p and 1 <= b <= 2,
[ BC0 - SUM ( Reserved(CTb,q) ) ] for q <= p and 0 <= b <= 2
]
The formula can be generalized to 8 active CTs and expressed in a
more compact way in the following:
"Unreserved TE-Class [i]" =
MIN [
[ BCc - SUM ( Reserved(CTb,q) ) ] for q <= p and c <= b <= 7,
[ BC(c-1) - SUM ( Reserved(CTb,q) ) ] for q <= p and (c-1)<= b <= 7,
. . .
[ BC0 - SUM ( Reserved(CTb,q) ) ] for q <= p and 0 <= b <= 7,
]
where:
TE-Class [i] <--> < CTc , preemption p>
in the configured TE-Class mapping.
6. Receiving Both Maximum Reservable Bandwidth and Bandwidth
Constraints sub-TLVs
[DSTE-PROTO] states that "A DS-TE LSR, which does advertise BCs, MUST
use the new "Bandwidth Constraints" sub-TLV (in addition to the
existing Maximum Reservable Bandwidth sub-TLV) to do so."
With RDM, BC0 is equal to the Maximum Reservable Bandwidth because
they both represent the aggregate constraint across all CTs. Thus, a
DS-TE LSR, receiving both the "Maximum Reservable Bw" sub-TLV and the
new "Bandwidth Constraints" sub-TLV (which contains BC0) for a given
link where the RDM model is used, MAY ignore the "Maximum Reservable
Bw" sub-TLV.
7. Security Considerations
Security considerations related to the use of DS-TE are discussed in
[DSTE-PROTO]. Those apply independently of the Bandwidth Constraints
Model, including RDM specified in this document.
8. IANA Considerations
[DSTE-PROTO] defines a new name space for "Bandwidth Constraints
Model Id". The guidelines for allocation of values in that name
space are detailed in section 13.1 of [DSTE-PROTO]. In accordance
Le Faucheur Experimental [Page 8]
RFC 4127 Russian Dolls Model for DS-TE June 2005
with these guidelines, the IANA has assigned a Bandwidth Constraints
Model Id for RDM from the range 0-239 (which is to be managed as per
the "Specification Required" policy defined in [IANA-CONS]).
Bandwidth Constraints Model Id 0 was allocated by IANA to RDM.
9. Acknowledgements
We thank Martin Tatham for his key contribution in this work.
Tatiana Renko is also warmly thanked for her instantiation of the
Russian Doll.
Le Faucheur Experimental [Page 9]
RFC 4127 Russian Dolls Model for DS-TE June 2005
Appendix A: Addressing [DSTE-REQ] Scenarios
This appendix provides examples of how the Russian Dolls Bandwidth
Constraints Model can be used to support each of the scenarios
described in [DSTE-REQ].
A.1. Scenario 1: Limiting Amount of Voice
By configuring on every link:
- Bandwidth Constraint 1 (for CT1 = Voice) = "certain percentage"
of link capacity
- BC0 (for CT1=Voice + CT0=Data) = link capacity
By configuring:
- every CT1/Voice TE-LSP with preemption = 0
- every CT0/Data TE-LSP with preemption = 1
DS-TE with the Russian Dolls Model will address all the requirements:
- amount of Voice traffic limited to desired percentage on every
link
- data traffic capable of using all remaining link capacity
- voice traffic capable of preempting other traffic
A.2. Scenario 2: Maintain Relative Proportion of Traffic Classes
By configuring on every link:
- BC2 (for CT2) = e.g., 45%
- BC1 (for CT1+CT2) = e.g., 80%
- BC0 (for CT0+CT1+CT2) = e.g., 100%
DS-TE with the RDM will ensure that the amount of traffic of each CT
established on a link is within acceptable levels as compared to the
resources allocated to the corresponding Diffserv Per Hop Behaviors
(PHBs) regardless of which order the LSPs are routed in, regardless
of which preemption priorities are used by which LSPs and regardless
of failure situations.
Le Faucheur Experimental [Page 10]
RFC 4127 Russian Dolls Model for DS-TE June 2005
By also configuring:
- every CT2/Voice TE-LSP with preemption = 0
- every CT1/Premium Data TE-LSP with preemption = 1
- every CT0/Best-Effort TE-LSP with preemption = 2
DS-TE with the Russian Dolls Model will also ensure that:
- CT2 Voice LSPs always have first preemption priority in order to
use the CT2 capacity
- CT1 Premium Data LSPs always have second preemption priority in
order to use the CT1 capacity
- Best-Effort can use up to link capacity of what is left by CT2
and CT1.
Optional automatic adjustment of Diffserv scheduling configuration
could be used for maintaining very strict relationships between the
amounts of established traffic of each Class Type and corresponding
Diffserv resources.
A.3. Scenario 3: Guaranteed Bandwidth Services
By configuring on every link:
- BC1 (for CT1) = "given" percentage of link bandwidth
(appropriate to achieve the Guaranteed Bandwidth service's QoS
objectives)
- BC0 (for CT0+CT1) = 100% of link bandwidth
DS-TE with the Russian Dolls Model will ensure that the amount of
Guaranteed Bandwidth Traffic established on every link remains below
the given percentage so that it will always meet its QoS objectives.
At the same time, it will allow traffic engineering of the rest of
the traffic such that links can be filled up.
Normative References
[DSTE-REQ] Le Faucheur, F. and W. Lai, "Requirements for Support
of Differentiated Services-aware MPLS Traffic
Engineering", RFC 3564, July 2003.
Le Faucheur Experimental [Page 11]
RFC 4127 Russian Dolls Model for DS-TE June 2005
[DSTE-PROTO] Le Faucheur, F., Ed., "Protocol Extensions for Support
of Diffserv-aware MPLS Traffic Engineering", RFC 4124,
June 2005.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[IANA-CONS] Narten, T. and H. Alvestrand, "Guidelines for Writing
an IANA Considerations Section in RFCs", BCP 26, RFC
2434, October 1998.
Informative References
[BC-CONS] Le Faucheur, F., "Considerations on Bandwidth
Constraints Model for DS-TE", Work in Progress, June
2002.
[BC-MODEL] Lai, W., "Bandwidth Constraints Models for
Differentiated Services (Diffserv)-aware MPLS Traffic
Engineering: Performance Evaluation", RFC 4128, June
2005.
[DSTE-MAM] Le Faucheur, F. and W. Lai, "Maximum Allocation
Bandwidth Constraints Model for Diffserv-aware MPLS
Traffic Engineering", RFC 4125, June 2005.
[GMPLS-RECOV] Lang, et al., "Generalized MPLS Recovery Functional
Specification", Work in Progress.
[MPLS-BACKUP] Vasseur, et al., "MPLS Traffic Engineering Fast
Reroute: Bypass Tunnel Path Computation for Bandwidth
Protection", Work in Progress.
Editor's Address
Francois Le Faucheur
Cisco Systems, Inc.
Village d'Entreprise Green Side - Batiment T3
400, Avenue de Roumanille
06410 Biot-Sophia Antipolis
France
Phone: +33 4 97 23 26 19
EMail: flefauch@cisco.com
Le Faucheur Experimental [Page 12]
RFC 4127 Russian Dolls Model for DS-TE June 2005
Full Copyright Statement
Copyright (C) The Internet Society (2005).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at ietf-
ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Le Faucheur Experimental [Page 13]
Html markup produced by rfcmarkup 1.129b, available from
https://tools.ietf.org/tools/rfcmarkup/
